printer nozzle clogging

Should first try to solution is to perform the print head cleaning operations, can perform a few times more.How to still can't solve the problem, is likely to be the integration of nozzle clogging in the ink cartridges.Generally speaking, the nozzle clogging can be divided into the nozzle and soft plug nozzle hard plug two kinds, their methods are different. Flexible nozzle clogging is caused by various reasons caused by ink viscosity on the nozzle bigger single-line breakdown.General with original ink box after many cleaning can be restored, but this way is a waste of ink.The simplest way is to use cleaning fluid (generally are sold each big computer city), fill in the ink cartridge after repeatedly perform the print head cleaning operation, right now than directly with the original cleaning the print head has a better effect. Hard plug refers to the nozzle with chemical coagulation or plug caused by impurities, the breakdown of the more difficult, must use artificial method to deal with.Must first'll take out the ink cartridge, the immersion after cleaning fluid and air can be loaded into the trailer again.As long as hard no damages to the nozzle electrode, after cleaning cartridge still can continue to use. As to how to save toner cartridge for after opening, longge Suggestions in open new ink packaging carefully open plastic block, keep the cartridge packaging complete.Until the cartridge temporarily need not when, just put it back in the plastic box, will lift block can use double-sided adhesive tape and box, to ensure that the cartridge is isolated.Of course, can also use a variety of other suitable container to store the cartridge, as long as pay attention to the lid joint strip seal was sealed. Z series of lexmark printer cartridges is integrated with the nozzle, thus the series of the original ink cartridge prices are higher.So, many users choose to use the refilling ink, more economical way. Fill ink in the use of the most common problem is in the process of nozzle clogging, especially in the long place are more likely to occur when not in use.The most common way to solve this problem is to use the printer nozzle cleaning procedures, general small congestion can be solved.But when encountered serious jam, you are washing on 100 times also not working.Don't worry, here I introduce a small doohickey. Put the cartridge nozzle part in about 50 ℃ ~ 60 ℃ hot water, pay attention to try not to wet the metal contacts, to avoid rust.Five or six minutes after take out the ink cartridge, wipe off the water near the metal contact.Then find a ultrasonic humidifier (note: be sure to use ultrasonic humidifier, do not use electric humidifier; jewelry shop or glasses shop ultrasonic cleaning machine can also use), to take away the water tank above, in the sink into a moderate amount of pure water, immerse cartridge nozzle down ultrasonic generator (is a bright metal.If can't find, can turn on the switch, to observe water mist surfaced from.Water mist is below the corresponding ultrasonic generator) at the top of the water. Then open the humidifier switch, touch the cartridge, you will find the cartridge in the vibration significantly.After about two minutes, can end.After cleaning, nozzle blockage has been ultrasonic oscillations out thoroughly.Mount the cartridge, you will find that the cartridge is as good as new. This method is also applicable to other brand printer cartridge nozzle integration all the cartridges. How to change the printer ink cartridges 1. EPSON EPSON printer cartridge slot step: after the EPSON printer cartridges used up, the printer automatically light up the red light, open the cover, press the red button beside, install the cartridge parts will be automatically removed, check the need to replace the ink cartridge, change is, mount after the reset, beside the red button again, the printer automatically detect movement. Wait a few minutes, can print. 2. CANON, HP, LEXMARK, lenovo in the cartridge, open the front cover, install the cartridge position automatically removed, check the need to replace the ink cartridge, change is, mount after the reset, cover to cover, the cartridge automatic reset, and the printer automatically detect movement. Wait a few minutes, can print.

http://www.juexiang.comin-china.com/catalogs/70/inkjet_printhead.html